Replacing Honda Front Struts - EricTheCarGuy
659 021
77.5
EricTheCarGuy1.81 млн
Следующее
28.03.10 – 21 6692:19Популярные
30 дней – 2 4870:53
30.07.21 – 207 89848:08Опубликовано 27 марта 2010, 20:36
Replacing Honda Front Struts - EricTheCarGuy
After posting the last video on replacing struts I thought I would post this one next. I shot this along with the rest of the Accord front end work that I did last fall. A couple of things are different, the most obvious is that the springs are a much smaller diameter so you really need to be careful when you work with these since the spring compressor doesn't have as much to grab hold of. Second, when you install the struts back on the car care must be taken to get the notch on the strut lined up with the wishbone, if you don't do this the upper wishbone bolt will not go in since it has to fit in a groove on the back of the strut.
For the second time I've shown you that I tighten the lower wishbone bolt with the car off of the ground, the fact is I shouldn't do this since I'm told it may ruin the bushing that goes through the lower control arm. I believe this to be possible but I have not experienced any problems doing it this way. For me it just seems like a pain in the butt to try and reach around the tire after I've put the wheel back on. But for those of you that like to point out my faults here is my excuse for not doing it the "right" way.
---
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
ericthecarguy.com
Visit EricTheCarGuy Forum
ericthecarguy.com/forum/defaul...
Visit my Facebook Page:
facebook.com/EricTheCarGuy
---
Be safe and stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
After posting the last video on replacing struts I thought I would post this one next. I shot this along with the rest of the Accord front end work that I did last fall. A couple of things are different, the most obvious is that the springs are a much smaller diameter so you really need to be careful when you work with these since the spring compressor doesn't have as much to grab hold of. Second, when you install the struts back on the car care must be taken to get the notch on the strut lined up with the wishbone, if you don't do this the upper wishbone bolt will not go in since it has to fit in a groove on the back of the strut.
For the second time I've shown you that I tighten the lower wishbone bolt with the car off of the ground, the fact is I shouldn't do this since I'm told it may ruin the bushing that goes through the lower control arm. I believe this to be possible but I have not experienced any problems doing it this way. For me it just seems like a pain in the butt to try and reach around the tire after I've put the wheel back on. But for those of you that like to point out my faults here is my excuse for not doing it the "right" way.
---
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
ericthecarguy.com
Visit EricTheCarGuy Forum
ericthecarguy.com/forum/defaul...
Visit my Facebook Page:
facebook.com/EricTheCarGuy
---
Be safe and stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.
Свежие видео
4 дня – 707 86642:11
9 дней – 3 4265:57
11 дней – 475 6090:38
15 дней – 118 27343:57
17 дней – 68 5090:18
17 дней – 107 9420:32Случайные видео
6 дней – 403 5661:45:28
211 дней – 94 07310:41
23.07.23 – 638 69115:13
17.06.21 – 1 488 9119:24
28.03.20 – 846 04710:46
25.11.18 – 317 5728:01
3 дня – 41 6270:37
4 дня – 7450:44
5 дней – 37 52120:09
9 дней – 56 01511:17
12 дней – 82 97111:34
13 дней – 268 53627:53
15 дней – 48 24912:51
3 дня – 222 61716:45
