Wooden Comic box // How-To | I Like To Make Stuff

Опубликовано 25 августа 2015, 11:06

I wanted to make a box to hold my comic books collection and I needed a reason to try out my Incra box joint jig.

What you'll need:
amzn.to/1IZxDbg - Wood glue
amzn.to/1JeObO3 - Table Saw
amzn.to/1SVz1Ub - Formby's Tung Oil Finish
amzn.to/1fqtm69 - Corner clamps
amzn.to/1fqt9Qf - Incra Box joint jig
amzn.to/1WFP9Zo - 8" dado stack
amzn.to/1hNmjpS - Trim router

I cut one piece of 1/2" plywood down to 24"x24". This will become the side panels.
I ripped another piece to 8 1/2" wide to use as the ends.
I switched out the blade for a dado set, so I could cut 1/4" dados.
I set the saw to only cut 1/4" deep.
I cut a dado every inch across the whole board.
I left 1 1/2" on each end.
This piece was cut in half, perpendicular to the dados.
I trimmed the end pieces to the same height as the side panels.
This is my first time using this Incra box joint jig. It takes a little bit to setup, but then it's very easy to use.
I clamped together the end pieces and cut finger joints on one side.
Keeping them lined up, I moved the clamps to the other side.
Then I cut matching fingers on the other edge.
I clamped together the side panels.
Then I cut fingers on both ends of the panels.
The cut outs were cleaned up with a rolled up piece of sandpaper.
On each piece, I clamped down a straight edge about 3" up.
I used this as a guide to cut a rabbet along the bottom edge of all four pieces.
I added glue to all of the cut outs, then assembled the finger joints.
The joints were tight enough to have to be forced together (that's good).
I used some clamping pressure to pull them all of the way together.
For glue drying, I added corner clamps to keep the corners square.
After it dried, I added glue to the rabbet.
I cut a piece of 1/4" mdf to fit and dropped it in place.
I added some weight to make good surface contact while the glue dried.

I set a stop block on my sled and cut several pieces of MDF to act as dividers.
1/4" was what I had on hand, but 1/8 would be a better choice.
I clamped the dividers and rounded the bottom corners, so they would slide into the dados easily.
Then I test fitted the dividers and sanded as needed.
With an orbital sander, I sanded all of the finger "tips" flush, being sure not to sand away the top layer of veneer.
The whole box got a couple of coats of varnish.
Then I just had to move over all of my comics!

Subscribe: bit.ly/ILikeToMakestuffSubscri...
Check out my TopVideos!: bit.ly/ILikeToMakeStuffTopVide...

Learn 3d modeling, get digital plans, and cool merch at
iliketomakestuff.com

Want to support ILTMS? Get exclusive content and more...
iliketomakestuff.com/patreon

FOLLOW:
instagram.com/iliketomakestuff
twitter.com/iliketomakestuff
facebook.com/iltms

#ILikeToMakeStuff

About I Like To Make Stuff:

We have lots of projects including woodworking, metalworking, electronics, 3D printing, prop making and more!

These videos are our attempt inspire and empower others to make the stuff that they want to have. Hopefully you'll see something here that will inspire you to make something that you're passionate about!

Wooden Comic box // How-To | I Like To Make Stuff
youtube.com/watch?v=eAIdpYQ7pq...

I Like To Make Stuff
youtube.com/Iliketomakestuff